GPIO/Remoting Error changing from UDP to TCP in OSC
GPIO/Remoting Error changing from UDP to TCP in OSC
After changing from UDP to TCP in Open Sound Control and clicking to enable, I get the error below every time I restart ProppFrexx, and clicking continue closes the programme. I've disabled OSC for the moment so ProppFrexx can be used.
13-Apr-19 8:02:08 PM [v4.0.5.25]:********** Error/Exception Information **********
Error Message: The requested address is not valid in its context
Error Type: System.Net.Sockets.SocketException
Error Source: System.Void DoBind(System.Net.EndPoint, System.Net.SocketAddress)
********** System Stack Trace **********
at System.Net.Sockets.Socket.DoBind(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Bind(EndPoint localEP)
at System.Net.Sockets.TcpListener.Start(Int32 backlog)
at ProppFrexx.RemoteControl.Osc.TcpServer.Start()
at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state)
at System.Threading.ThreadHelper.ThreadStart()
********** End **********
13-Apr-19 8:02:08 PM [v4.0.5.25]:********** Error/Exception Information **********
Error Message: The requested address is not valid in its context
Error Type: System.Net.Sockets.SocketException
Error Source: System.Void DoBind(System.Net.EndPoint, System.Net.SocketAddress)
********** System Stack Trace **********
at System.Net.Sockets.Socket.DoBind(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Bind(EndPoint localEP)
at System.Net.Sockets.TcpListener.Start(Int32 backlog)
at ProppFrexx.RemoteControl.Osc.TcpServer.Start()
at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean preserveSyncCtx)
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state)
at System.Threading.ThreadHelper.ThreadStart()
********** End **********
Re: GPIO/Remoting Error changing from UDP to TCP in OSC
Seems you have specified an invalid endpoint address?!
With what other device or software do you try to use OSC? As by default it should use UDP.
With what other device or software do you try to use OSC? As by default it should use UDP.
Bernd - radio42
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution
Re: GPIO/Remoting Error changing from UDP to TCP in OSC
yes silly mistake. pointing to the wrong IP. I was able to change it while the error message was still on screen. I did not expect it would crash ProppFrexx though.
Re: GPIO/Remoting Error changing from UDP to TCP in OSC
Yes, it shouldn’t - I’ll see to prevent this.
Bernd - radio42
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution
Re: GPIO/Remoting Error changing from UDP to TCP in OSC
Should now be fixed in v4.0.5.27.
Bernd - radio42
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution
ProppFrexx ONAIR - The Playout and Broadcast Automation Solution